Warehouses & factories

Machine Pre-Use Check App: How to Get Operator Checks Off Paper

How to move machine pre-use checks off paper: what PUWER expects, what a good check covers and what to look for in an app. Free 2-week trial.

By Rhys Lowry, Checkmate Safety · · 6 min read

Most factories already have a pre-use check for their machines. It's a sheet on a clipboard by the press, the lathe or the bandsaw, and the operator is meant to tick it at the start of every shift. The trouble is what happens to that sheet next. It gets ticked in bulk at the end of the week, a fault gets written in the margin and never reaches maintenance, or the sheet goes missing the week you need it.

A machine pre-use check app moves that check onto the operator's phone. This guide covers what UK law expects, what a good pre-use check includes, and what to look for in an app so the checks actually get done.

What the law says about machine pre-use checks

The Provision and Use of Work Equipment Regulations 1998 (PUWER) put the duty on the employer. Regulation 5 says work equipment must be "maintained in an efficient state, in efficient working order and in good repair", and that where a machine has a maintenance log, the log is kept up to date. Regulation 6 covers inspection where the way a machine is used could lead to danger if it deteriorates.

HSE's guidance is practical about it. For a lot of equipment, it says, "a quick visual check before use will be sufficient", for example checking the cable on a hand-held power tool or testing brakes. Anyone with enough knowledge and experience of the machine can do it, which in most workshops means a trained operator.

Two points often get missed. HSE says records are "not normally required" for the simplest pre-use checks, but where you carry out a formal inspection the result should be recorded and kept at least until the next one. And if your risk assessment or safe system of work relies on pre-use checks, you need to be able to show they happen. A pile of half-ticked sheets doesn't do that. For the formal side, see our guide to PUWER inspections. This is general guidance, not legal advice.

What a good machine pre-use check covers

Keep it short enough that an operator will do it properly in two or three minutes. For most production machines that means:

The checklist should be different for each type of machine. A generic sheet that covers "all equipment" ends up full of questions that don't apply, and operators learn to tick through it without reading. Our free machine guarding inspection checklist is a good starting point.

Why paper pre-use checks fall down

Paper works until someone looks closely at it. The usual problems are:

When a machine fails or someone gets hurt, these are the gaps an HSE inspector or insurer will ask about. Our article on how inspection records protect managers goes into that in more detail.

What to look for in a machine pre-use check app

Plenty of apps let you build a checklist. For machine checks, a few features matter more than the rest.

Proof the operator was at the machine

If the app only needs a login, a check can still be done from anywhere. Look for something that ties the check to the machine itself, such as a tag or device the operator has to scan before the checklist opens.

A visible status on the shop floor

Supervisors shouldn't have to open a laptop to find out whether the morning checks are done. With Checkmate, each machine has a small device with a light that flashes red when a check is due and turns green once it's done, so a walk down the line tells you where you stand.

Defects that reach maintenance straight away

When an operator fails an item, they should be able to take a photo and have it go straight to whoever fixes it. That's how a worn belt gets replaced on Tuesday instead of snapping on Friday.

Checklists you can change yourself

Every machine is different, and checklists change after a near miss or when a new guard goes on. You should be able to edit them yourself without paying a developer.

Pricing that doesn't punish you for adding people

Some systems charge per user, which pushes companies to share logins and defeats the point. With unlimited users, every operator has their own account and every check carries a name.

How to switch from paper without a big rollout

You don't need to do the whole factory in one go.

  1. Pick three or four machines that are used every shift, ideally ones that have had faults before.
  2. Copy your existing paper checklist into the app, then cut anything that doesn't apply to that machine.
  3. Show the operators on those machines how to scan and complete a check. It takes a few minutes.
  4. Run it for a week or two, then look at what came through: missed checks, completion times and defects raised.
  5. Roll it out line by line once the first machines are working.

Checkmate offers a free two-week trial for exactly this, so you can see it working on your own machines before committing. Subscriptions start at £100 a month depending on how many assets you have, with hardware bought separately at a fixed price.

Frequently asked questions

Do machine pre-use checks have to be recorded by law?

HSE says records are not normally required for the simplest pre-use checks. Formal inspections under PUWER regulation 6 should be recorded and the record kept at least until the next inspection. Many businesses record pre-use checks anyway, because it's the only way to show they happen.

Who can carry out a pre-use check on a machine?

Anyone with enough knowledge and experience of the machine to know what to look at, what to look for and what to do if something's wrong. In most workplaces that's a trained operator.

How long does a digital pre-use check take?

A well-written checklist of eight to ten items usually takes two or three minutes. Scanning the machine and tapping through on a phone is normally quicker than finding a pen and filling in a sheet.

What happens when an operator finds a fault?

With Checkmate, the operator marks the item as failed and uploads a photo of the defect. Managers see it straight away, and the machine's record shows when the fault was found and who found it.

Is a pre-use check the same as a LOLER thorough examination?

No. A LOLER thorough examination is a detailed examination of lifting equipment by a competent person at set intervals. Daily pre-use checks sit alongside it. See LOLER thorough examinations vs daily checks.

Try it on your own machines

If your machine checks are still on paper, try Checkmate free for two weeks on a few machines and see what comes through. Start your free trial at checkmate-uk.co.uk or call Rhys on 07882 236560.